This is the second pattern in the pumpkin series, and is a much more reasonable design as compared to the extra large extravaganza I felt the need to make before. This you will find, is much more in line with the crocheted pumpkins that are littered all over Pinterest. This free pattern will walk you through how to make a pumpkin just as pictured, and even create the little bow styled stem on top, something I found to be a little more classic then the stem style I used in the other project. What is nice about this pattern is it is very customizable! It incorporates a rectangle that is sewn together, and can be adjusted to any size to make a larger or smaller pumpkin.
For many of my stuffed patterns I like to use a nylon stuffing, something I found my friend doing and thought was brilliant, but in this case I did not feel there was a need as the crochet hook I used was several sizes smaller then suggested, and filled in any stitch gap you would commonly find. It also made it a bit of a pain to keep the stitch count, and I suspect I didn’t, but as I sewed the 2 edges together it didn’t matter and I made the line up. So in the event you find your stitches are no longer the length you started with don’t fret just sew it, or if you have gaps between the stitches because you don’t want the annoyance of a super small hook, consider nylon stockings to stuff instead of the pumpkin directly. Those would be my construction tips for this project.

MATERIALS
- 4 mm crochet hook
- Baby Bee Adore-A-Ball Yarn in Forest
- size 5 bulky
- 1 skein
- Baby Bee Adore-A-Ball Yarn in Burnt Pumpkin
- size 5 bulky
- 1 skein
- Embroidery Needle
- Stuffing
Please note that the yarn I used is from Hobby Lobby, where you can purchase Yarn Bee and Baby Bee brands (This is not a promotion, there just happens to be a hobby lobby less than a mile from me). They almost never have the colors available so I will not link them, but I will note that any velour or silky yarn in a size 5 bulky will work!
Also, This post may contain affiliate links designed to provide a commission on purchases made at no cost to you. As an Amazon Associate, I earn from qualifying purchases that support my work in providing new content and information on this site.
ABBREVIATIONS
HDC – Half Double Crochet
BLO – Back Loop Only
SLST – Slip stitch
DC – Double Crochet
CONSTRUCTION
The Pumpkin Body
Row 1: Chain 20 + 2 to turn
Row 2: In the 3rd loop, HDC in BLO – repeat to the end
Row 3: Chain 2 to turn, HDC in BLO for all stitches
Row 4 – 25: Repeat row 3
In last row, SLST to tie of leaving an extra long tail. use this tail to sew the 2 rows together and sew closed the top of the pumpkin.
To sew closed, fold the rectangle in half and using a embroidery needle, simply sew each stitch together. You don’t need to be too concerned with how the seam will look as it will not be visible once the grooves are added.


Once the ends are sewn together, sew the bottom of the pumpkin closed. Again, you don’t need to worry too much about appearance, but to make sure it is completely secured, try sewing in only the outer loops of each row and even skipping every other stitch to completely close the bottom and eventually the top.
Tip: I initially sewed through every stitch for the bottom and found there was a gap, so instead of going through again I made a little circle with a magic circle, increasing every stitch and then alternating an increase and single stitch and just stuffed that in the bottom of the pumpkin to close the gap. I found by alternating in each stitch on the top I did not face this same predicament!

Once the bottom is sewn shut, stuff the pumpkin, push the tail and needle up through the bottom to the top and repeat the steps to close. Make sure to completely stuff the pumpkin, but not to the point that it is pushing out and tight. You want some slack for the grooves!
To add the groves, you are going to take the tail and wrap it around and back through the center several times. I did a total of 5, but it is completely discretionary. Each time you wrap around the pumpkin make sure to pull tightly, causing the yarn to push into the ball creating an edge.
BE CAREFUL HERE if you are using the Adore-A-Ball yarn because it is weak and can break!! I actually did break the yarn and found I could just tie it back together and hide it within the middle of the pumpkin and complete all my grooves.
But with that, the body of your pumpkin is complete!
The Leaves
Row 1: Chain 50 +3 to turn
Row 2: In the 4th stitch, DC 3 times into the same stitch – Repeat to the end of the chain

To add the stem and leaves I chose to connect them like a bow. I folded the chain in half, secured the 2 sides together, and then secured the middle of the loop to where I sewed the sides together. Once this was done, using the same piece of yarn, I looped the stem to the pumpkin a few times. I knotted this and hid the tail within the pumpkin, and with that I was done.

The diagram above is made in the classic and world renowned windows application, paint, but I hope it helps visualize what I mean. All in all it was a quick and fun project, and I am excited to make a few more so that, like many millennials, I can litter my home with pumpkins during the fall season, giving my darling husband a headache and internal questioning of if he made the right decision to marry me.




